DIY火灾地点/坑

21,914

二百三十四

7

About: I teach Grade 8 and DIY as often as I can.试着让别人找到他们的创造性的一面,用他们能做的去建立/创造!

想让你的后院有一个很好的口音,but tight on space?Try this DIY Fire Place/Pit Build that has a high back wall so that you can keep it tight to a side fence (not too tight though) or in a corner.它最适合半圆形座位,让您的所有客人都能感受到热量!

第1步:材料

Hopefully you have a truck like me,如果不去租一个或使用你的电话,朋友生命线,因为它是更便宜的方式,去你当地的花园中心,并购买半码的破碎机运行(通常称为“粉碎”)。You will only use a fraction of that 1/2 yard so make sure you have a place to store the rest.如果你不这样做,尽管付了1/2的价钱,但还是请花园中心的伙计们/姑娘们给你1/4的。

For the stones,打起kijiji,或者四处找任何正在清理石头的人。我很幸运,当我为一个朋友建造甲板时,他想把院子里所有的石头都扔掉,而不是把它们留在甲板下……所以我拿走了它们!Having these stones is what began this project in the first place,所以如果你发现自己有一堆石头,这可能是一个让它们发挥作用的项目。

工具:

  • 水平
  • tape measure
  • edging shovel
  • 铲子
  • hand tamp
  • 标记漆

第2步:标记和挖掘

  1. 用你的记号漆标出你想去的地方。我做了我的4ft x 4ft,这样我的石头就越合适越好。一个很好的主意是在你划出记号,看看你得到的是什么尺寸的东西之前,用你的石头做一些数学计算。
  2. Using your edging shovel,在线的外侧挖洞(挖洞要比划线大一点,这样铺设更容易)。试着把成绩降到4-5“以下。
  3. 用铲子和边铲清除标记区域内的所有污垢,尽量使其在地面以下4-5“处平整。
  4. Using your hand tamp,tamp the dirt down to give yourself a flat/level working surface.如果土不太平整,就把它耙出来。

第3步:回填和平整

  1. 用铲子把新挖的地方填满你的碎石。你要把它耙出来,尽量保持水平。Backfill about 1-2",耙出,然后用你的手把它捣实。Go hard at it with that hand tamp!Great tricep workout.
  2. Repeat that step until you are about 1/2" below the grass grade.
  3. 利用你的水平,make sure that your outside is level on all four sides and on the diagonals.如果不水平,耙子,填充,and tamp until it is.

第4步:生成底行

  1. 抓住你的石头,开始把你的基地排在一个角落。
  2. Work out both directions from that corner.Until you get to the adjacent corners.完成最后一面,直到基本行完成。There is no need to use a tape measure to check for 'square' if your stones are all the same size.确保对面有相同的石头,并且所有的角都对齐……在步骤1中,你把洞做得比实际想要的大一点,这样做会更容易。你的坑不必与你挖的地方成直角,因为你将在你挖的地方周围进行回填。
  3. Make sure all four sides are level.如果不是,用你的体重(或橡皮槌)使石头水平…这第一个基础排周围是最重要的!毕竟,一个结构只有它的基础一样好。

Step 5: Build Up

  1. 用剩下的石头,建立!Be sure to overlap the bricks in a pattern so that the edges of each brick do not line up.This is especially important on the corners.我必须建立,然后拆开,然后再次建立,以确保我是使最少的边缘对齐。慢慢来,在进入下一个之前,确保你完成了一整排。

Step 6: Keep Building Up

Continue laying rows until you get your desired height/look.如果可能的话,我建议在一些较低的排上创造一些“气流”,以帮助获得所需的“氧气”,以帮助燃烧你的火焰。我在后墙(最高的墙)的一半处做了我的。I really like symmetry,所以这只是我在设计上的一点小小接触。

一旦你得到了你想要的,load up the pit and light it up!

作为最后的建议,I had some leftover concrete from a previous build,所以我混合了一点,然后把它倒在底部。This is a great move because then you have a true 'base' after each fire and you don't continually dig more and more of your pit out when you are cleaning out the ashes...once you've hit the concrete,不要再挖了!

Share

    建议

    • 1小时挑战

      1小时挑战
    • 冷冻食品挑战

      冷冻食品挑战
    • 美容技巧比赛

      美容技巧比赛

    7讨论

    0
    None
    CokeLady53

    8个月前

    想知道照片中的水泥搅拌机。Did you use cement between the layers?

    0
    None
    JasonL237

    8个月前的Step 6

    Have you looked at using a Rumford fireplace pattern?如果你使用这种模式,你的团队会得到更多的热量辐射。干得好!我喜欢你选择的多色方块。

    0
    None
    精神病患者6153

    8个月前

    What I like about this project is the budget and the look.很好。

    0
    None
    哈尔普

    8个月前

    Hmmm,我不是专家,但是用来放壁炉的砖是专门做的,里面没有湿气。我的理解是,不这样做的砖在受热时会爆炸。Maybe somebody who knows for sure can chime in.

    2 replies
    1
    None
    DIY学院 哈尔普

    Reply 8 months ago

    我也听说过这个问题,设计的一部分是通过策略性地分离砖块并在砖块之间留出空间来确保“气流”,但也不能用耐热粘合剂将“铺路机”永久地连接在一起,让它们有“呼吸的空间”。此外,I used these pavers after a friend of mine had already used them for many fires and was my essential test.

    1
    None
    信号兵 哈尔普

    Reply 8 months ago

    What you are saying is true and that was my critique coming to the comment section.However,Ive built firepits from standard construction bricks before and had them heated at VERY high temps without a single explosion.So my .02 is that you can get away with using regular bricks but proceed with caution on your first fire.

    1
    None
    烧烤啤酒

    小费8个月前

    Very nice project!只是想扔进去,检查当地建筑和消防规范。Around here,在任何建筑物或围栏10英尺范围内都不能有消防坑/场所。我还担心那棵灌木会干枯着火。