如何清洗粘橡胶

176,935

375

95.

简介:如何清洁粘性橡胶

About: I've always liked pulling things apart - it's the putting back together again that I have some issues with!

在许多产品如电子产品上,橡胶被添加以帮助握把。有时,由于环境条件,如温度和紫外线照射,橡胶会分解,变得粘。你可能自己也会遇到这种情况,因为橡胶的行为很常见。

这种可指示的可指示将通过一些关于如何从产品中删除此粘性混乱的方法。

So why does rubber do this? Natural or synthetic rubber starts out as a very sticky substance. That’s because the molecules in the raw state are long chains of very weak links to each other. To turn that raw material into the rubber we all know and love, you have to put it through a process called vulcanisation. This involves heating the rubber with some other chemicals, which molecularly transforms the rubber from sticky to stretchy.

The vulcanised rubber though can revert back to it’s original state under certain conditions. It happens when the stronger polymer crosslinks get snipped and the molecules revert back into their original small chains. Once that happens you’re stuck with rubber that has become sticky and tacky.

在以下说明中,我会通过几种方法来删除这种混乱,并希望为您提供几个指针如何自己做。

第1步:工具和准备

工具

190%异丙基溶液。你可以从药店或五金店拿到这个。

2. I have also used Methylated sprits which can be purchased from a hardware store or even your local supermarket. It seems that methylated spirits is called by a few different names. In the US there's something similar called denatured alcohol (be careful of denatured alcohol though as it has Methanol in it which can be very dangerous). I've also heard that this can be damaging to plastic so be wary using it to remove rubber and do a test first. There is also methyl hydrate, or fondue fuel available in the US as well. Again I would do a test first to see how well these work before using it. In Europe, it may be called spirits. check out这个链接了解更多

准备

1.确保您在工作的区域是干净的

2.将布放在你工作的工作区上。

3. Have some spare cloths handy to remove any excess chemicals

4. It’s good practice to also wear rubber gloves and some safety glasses as well. The isopropyl can be absorbed into the skin, which can cause poisoning in large amounts. Small amounts though isn’t considered dangerous

步骤2:方法1 - 使用异丙基

The first method I'm going to show is using Isopropyl. Isopropyl is what is known as a synthetic alcohol and can be found in things like shaving creme, antiseptic and industrial applications.

虽然它是易燃的,但异丙基是非常良性的。但是,如果使用大量使用,您应该尝试戴手套。如果用大量使用,它可以容易地吸收到皮肤中。

我决定在我最近购买的嗨8相机上使用异丙基。顶部的一些橡胶非常非常粘稠,胶粘剂,我猜是它以5美元的价格销售的原因!

Steps:

1. Place the camera on a clean surface

2. Next, apply some Isopropyl to the affected area, adding enough to cover the rubber.

三。小心不要将异丙醇过多地进入任何电子领域,如开关或小开口。但是,如果你这样做,不要太过紧张,异丙基会迅速蒸发,不应该影响电子设备(手指交叉!)

4.开始用干净的布擦拭橡胶。你需要擦拭的努力将取决于橡胶的程度如何。在这款相机上,橡胶很容易离开。

步骤3:方法1-重新应用

As the Isopropyl evaporates quickly, you’ll probably need to re-apply a few times

Steps:

1. Once the Isopropyl starts to dry and you find that the cloth is sticking to the rubber, it’s time to add another layer of Isopropyl.

2.继续在橡胶上涂抹并用布摩擦。每次使用布料清洁部分。

3.一旦所有橡胶被拆除,就应该只用橡胶粘附的裸塑料。

4. Give it a final wipe with a clean cloth and you’re done! You should then power-up the part and ensure it still works ok.

步骤4:方法2-使用甲基化烈性

我通常会去除橡胶时甲基化泉水,或者如果你在美国,那么变性酒精。我发现它与橡胶效果很好,这是迄今为止退化的橡胶。我用它的相机是粘稠的,但不会像Hi-8摄像机一样退化

Steps:

1.将一些甲基化泉水加到清洁布上

2.开始擦去橡胶。如果你发现橡胶没有脱落(就像我用这种相机这样的情况),你需要多次申请

3.在塑料上摩擦,最终将橡胶开始移除。

4.保持施加和摩擦,直到所有的橡胶表面消失。

5. Give the part a final wipe over and test to make sure it still works

Fix It Contest

Runner Up in the
Fix It Contest

2人制作了这个项目!

Recommendations

  • 让它发光比赛

    让它发光比赛
  • 第一次作家比赛

    第一次作家比赛
  • 任何比赛

    任何比赛

95讨论

0
Stephen.goff01

17小时前Step 4

Pure Acetone, used in very small quantities worked extemely well. A few passes with a tissue that was dampened removed the top layer. I now have a shiney smoth surface on my Bluetooth speaker. Problem solved.

1
yuggy.

9天前

I may be old... but about 40 years ago an instructable like this would go like:
___
从电子产品中取出粘性橡胶涂料:
Rub it with Isopropyl Alcohol or Methylated Sprits.

...我怀念那些日子...

THANK YOU for this. I used isopropyl alcohol and scraped off the top sticky layers of rubber. What remains is non-sticky rubber.

0
throbscottle

12 days ago

我喜欢橡胶涂层,并希望有指令恢复到不粘的状态,或者只是清洁表面上的粘滞!我认为它是我手中的物质,使它变得这样。那好吧...
也许我会按别人的建议试试滑石粉。

0
索卡图勒人

Question15天前Step 4

You mentioned using the camcorder to transfer the Hi8 to digital. Would you explain how to go about that? I have some old tapes that I'd love to move over to my computer. Thanks for the tip on the rubber improvement. I've had that problem too.

0
索卡图勒人

14天前回复

Thanks for your reply but neither of those links works. Can you check and make sure they are still valid on your end? Thanks again.

0
Lonesoulsurfer

14天前回复

这是你的一些图像,所以你可以自己看起来。只需将视频转换器键入亚马逊即可找到它们

0
索卡图勒人

14天前回复

谢谢你的帮助。我会去做。再次感谢。

0
Mooremob.

15天前

我用婴儿粉粘上“橡胶”的那一种似乎有效的纸巾,IPA是一种很好的溶剂会尝试一下。
另一种从标签中提取粘渣的好溶剂是桉树油。

0
ThummarwitshW

15天前

哇!这就是我在寻找的。超过10年,我发现了许多我的东西粘稠。我会去清洁它。非常感谢您的分享。

0
TCS79

15天前

I use WD40 one time, and work fine. The piece became a little oilled afterwards, but with a paper towel I remove the residual oil and was ready to go. Thanks for this other options.

4
LaserJoe.

Question11个月前

Just wondering what you or anyone has done to replace the grippy layer that was removed?

0
布里斯巴尼布莱斯特

答案15天前

If it's a round handle, you can use heat shrink tubing. I have also used that on small wheels, trimming the edges. If really lazy (too much to do, too little time), I may heat shrink over it, assuming it's flat.

1
内诺恩

3个月前的答复

我用曲棍球握在钳子上,看起来很好

2
Ron Jeremy

回答9个月前

就个人而言,有大多数有这种表面的物品(并且我清理它们),我就可以完全可以用底层塑料,易于清洁,它不能像讨厌的橡胶表面一样轻松分解。所以我就像他们一样使用它们 - 现在包括Mouses / Mice(?),3D鼠标,键盘,读卡器,无线电臂架......
If you really really need to treat surface with something rubbery, you may try to search for "Plastidip", although I would do that only for things that really really require firm, non-slippery grip. It's used to cover car rims like a paint, and one day when you will feel unhappy with it, it might be peeled off.

5
Emardee.

11个月前回答

There are products that replicate the grippy rubber layer. You can get it at your local hardware store. Comes in two forms:
1)液体,使部件浸入 - 适用于螺丝刀手柄等。
2) 一种像油漆一样涂上的喷雾,适用于诸如摄像机等精致物品的表面,或者在你遮掩了一个区域以应用于较小的补丁。

注意我从未使用过这些产品中的任何一个,但我在将整车的人互联网上看到了这些东西!我的猜测将是成功的结果,对于任何项目都会取决于良好的附着力,这将取决于良好的表面准备。
有人试过这些产品吗?任何好吗?

0
电弗兰克

15天前

当其他事情失败时,我使用Modeller的油漆剥离器,可从型号商店获得。
它的设计是为了去除许多原始油漆,而不伤害下面的塑料。
它的东西很强,所以保护手,不要呼吸它。

0
马基蒂雷

15天前

我只是在它上擦了一点滑石粉,它不再粘。也许我错过了那点或只是玩酒精的乐趣。。。