Flip Top Planer Stand

如果您喜欢我，您的工作室中的工具空间有限，Aka车库。我能说什么，我喜欢工具，但我的单车车库已经狭窄，我几乎无法四处走动，更不用说找到房间来建造一些东西。我迫切需要做点什么来拯救一些空间并优化布局。

我遇到的简单解决方案是一个翻转顶级工具架，它允许您在1的空间中存储2个工具，同时让它们轻松访问并在需要时使用。

This design was inspired by Brad atFixThisBuildThat如果您有兴趣，他已经为此构建提供了计划。Get the PLANS from FixThisBuildThat HERE(specs may vary).

My stand's dimensions were intended to accommodate a德瓦尔特DW735刨床和一个Ridgid oscillating spindle sander。

This planer stand has a super solid locking system that's easy to make, and I'll show you how.

这是您需要的硬件：

• （4）5/16 x 3-½“吊环螺栓
• （4）5/16挡泥板垫圈
• （4）5/16 star knobs
• （4）⅜x 1-½“六角螺栓
• (8)⅜垫圈
• （4）⅜坚果
• （1）¾ O.D. steel pipe 36” long
• （4）3“锁定脚轮轮子
• (16)#14 x ¾” wood screws
• (8)＃8 x 3-½“木螺钉
• 1-1/4″ pocket hole screws
• 1-1/4″ wood screws

Start by cutting down some 3/4 plywood:

• 2 equally sized pieces that will be used for the side panels
• 4 equally sized pieces that will be all the horizontal pieces (bottom, shelf, platform faces)

Drill pocket holes into the side edges of the bottom and shelf pieces. Attach the bottom to both side panels using口袋螺丝。

然后将一些间隔块切割成架子到位，并从使用更多的口袋螺钉将其拧到侧板上。

Lastly, cut a piece for the back and secure with pocket screws.

To make a really simple no frills drawer, cut 4 pieces of plywood to make a box that will be 1/8" smaller than the height, width and depth of the opening. No slides are necessary, not even a drawer face.

使用桌子锯切割浅槽，以便容纳抽屉底部。

该n, using pocket screws, assemble 3 sides, but slide in the drawer bottom before attaching the 4th side.

首先追踪从每个侧面面板的顶部向下追踪2英寸。它有助于将内阁置于此步骤。

Find the center of the line and drill a hole using a 3/4 Forstner bit. This will accommodate the steel pipe that rotates the tabletop.

Use a 5/16 drill bit to drill a hole on the line, 1-1/2" in from the edge. Do this on both the front and back edges. With a square, extend the sides of the hole to the edge of the plywood and use a jigsaw to cut out a notch.

Oh and while the cabinet is on its side, it's a good time to mount the3" locking caster wheelsusing some#14 3/4螺钉。

Grab one of those 4 pieces you cut at the first step for the platform.

切割4件1x2松树，与平台相同。

铺设胶合板板平板，并找到前部的中心线，然后在每侧测量3/8英寸。对接一块1x2松木，向上每个线条，并使用1-1 / 4“木螺钉（第一钻埋头腔飞行员）。这将是Nook的钢管。

另2松片需要一个等级的e ends. Make a simple jig that will ride along your table saw’s fence to make a 5/16 notch in the center of the boards, that’s 1-½ inch deep. Then screw these pieces down flush with the outside edges of the plywood.

通过添加更多1x2件周围完成周边。

在密封平台之前，重要的是在您安装的工具下添加阻塞，因此您将有一些才能拧入。如果您使用螺丝，则需要确保将块绑定在较小的孔下，如果您正在使用螺栓，则较大的孔。

Seal up the platform with the other piece of plywood using 1-1/4" screws.

For each corner of the platform, do the following to assemble the hardware:

1. 用组合方块在距离每边1英寸处做标记。
2. Make a recessed hole using a Forstner bit, approx. 1/2 inch deep. Do this on both the top an bottom sides of the platform.
3. 用3/8钻头在中心钻一个孔。
4. Insert the head of theeyeboltinto the cavity.
5. 将3/8垫圈滑入凹槽，然后是a3/8六角螺栓。
6. 滑动A.nother 3/8 washer onto the end of the bolt from underneath.
7. Add a 3/8 nut.
8. 滑动A.挡泥板（或常规）5/16垫圈上的吊杆，然后是一个star knob。

Mount the platform onto the base by threading the3/4" steel pipethrough the hole in the side panel and the cavity in the platform.

Cut down the excess steel pipe using a hack saw, leaving 1/2" protruding from each side.

使用3/4 forstner位，使凹陷成一组胶合板块，1/2深。将这些块安装在管道上并使用1-1 / 4“螺钉将其拧到机柜上。

Mount the tools using 3-1/2" screws (smaller holes) or拉力螺钉(larger holes), centering the tool front to back.

对于电线管理，我用一块皮革，用压力扣，我拧到平台上。这将是一种快速简便的方法，可以保持线索和脱离方式。

现在，让我告诉你，我第一次将工具翻过来我很紧张！该刨床单独的重量约为90磅......但是当我看到平台旋转的平稳时，我的所有恐惧都融化了，并且一个新的工具神奇地被围起到位。

_________________________

如果你还没有，一定要看看视频。如果你喜欢你所看到的，订阅我的YouTube频道当我发布新的项目视频时得到通知。

More from DIY Montreal:

• Router Table & Fence Build
• Drill Press Table
• 逐渐变细汰缘